Procedures to recover your box k...
With the USB_Burning_Tool software
install It
- Download the img according to your receiver
KIII PRO
KIII_PRO_AVL6862-NHG47L-20170905.174619.V0619.img
KI PRO
https://mega.nz/#!ZwQRGCZJ!pY95UxqBIfVPMom6YnMWBSA67oL0u5g9ZW60cekCheE
KIII_PRO_AVL6862-NHG47L-20170905.174619.V0619.img
KI PRO
https://mega.nz/#!ZwQRGCZJ!pY95UxqBIfVPMom6YnMWBSA67oL0u5g9ZW60cekCheE
- use a USB cable usb male male
- plug one side into the receiver
- A. Start USB_Burning_Tool
- B. change language
- Click "File" and choose "Import image", choose the .img of your receiver
- Remove the power cable
- now click on Start
- click on the RESET hole behind, while still resting, connect the other end of the USB cable to your PC and connect the power supply while still being supported
You hear the sound of the connection "connect" it's ok let go
he starts ... leave - Or you can also stay press the blue button in front of or place of the reset
- once finished remove and test the
in the case of non-recognition by the pc changes usb port on the box using the one below the sd card and start again
With card sd How to do?
The box turns under amlogic, tools exist for its last to bypass a brick or just for an initial flash. They use either the OTG function (but the box only has USB A, and a USB cable male to male is not common ....), Or via a SD card, and it falls well there is a port on the box!We will need:
- An img file to download at the top according to your box
- Burn Card Maker here
- A micro SD of 2GB minimum.
Implementation :
- Launch Burn Card Maker, basic it is in Chinese, to pass in English click on the top left then on the second line:
- Once validate, restart the app then configure it as in the image below (the address of the SD player is probably different at home). Rename the burn package to "update.img" otherwise the flash will fail on the box.
- The app will ask you to format the SD card, made "Ok" then "Close" once finished
- clinic on make
- Let the app unpack the burn package on the sd, once finished your sd is ready for the jobs.
Flash of the box
Now that the SD is ready we can finally flash the box, it is going to be done to respect the following procedure:- Connect your box in HDMI to your "important" tv
- Disconnect the power supply and insert the micro SD into the reader
- Flip the box and hold down the button via the access slot (via a toothpick, trombone ect ....) For 5s
- Connect (while holding down the button) the power cable
- The following image should appear, you can release the button and let the flash finish
- The box restarts at the end of the flash, remove the micro sd, the initial boot will be long enough is normal.
- You arrive on the home screen, congratulations your box is under android TV
Hi. I have bricked Mecool K1 Plus S905D. There is no HDMI signal. I tried update several firmwares via SD card and USB (male to male) and nothing.
RépondreSupprimerIf I trying upload firmware by AMlogic USB Burning Tool software, shows error:
[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
What should I do? Do you have any solution of this issue?
If it posible, please send me newest firmware (IMG file).
Best regards,
Jaroslaw Hudyga
Fixed firmware for S905D SoC based KI Plus (1G/8G) in .img format for USB Burning Tool:
RépondreSupprimerhttps://disk.yandex.com/d/01RUEGcKk_V0BQ
I have a Mecool K3 RARE and need the .img to this box.~
RépondreSupprimerCan you help me?
Thanks in advaNCE.
Also need channels list of satellite for KIII Pro (AStra and Hotbird)